How To Safely Use Car Jack Stands

Instead of socket wrenches, screwdrivers, and pliers, the most effective tools in your garage are the ones that keep you and others safe while working. If you were to lose the use of your legs, hands, or eyesight, it would be much more difficult to work on your car. The jack stand is one of the most important pieces of safety equipment, and it’s critical that you also have at least 4 of them on hand.

Each time people jack up their car; they should use a jack stand to keep it from falling down. If this is unfamiliar work for you, it is critical that you become familiar with these gadgets or how to utilize them, and this article will teach you everything you need to know.

About Jack Stand

How To Safely Use Car Jack Stands

The jack stand is indeed a simple device that is made of metal and can be adjusted in height and is used to take the weight of any raised vehicle. Most of the time, they are positioned under the vehicle as a support system to prevent a car from crashing into a person or object.

Here are some simple steps that can be followed for safely using car jack stands

1. Place the car in a safe location and lock it

  • If at all possible, park the vehicle on solid ground on a paved road. You should station your car close to the curb & roll the wheels inward if you need to park on an ascent to save time.
  • Block the wheels on the downside with tire wedges, woodblocks, or masonry to protect the wheels from unintentionally rolling back up the slope. If you’re raising the front of the car, you should check the rear tire, and vice versa for the back wheels.
  • Place the car in the parking position and press the emergency brake to avoid a collision. If the vehicle has a manual transmission, shift it into first gear while maintaining control over the parking brake.

2. Position the Jack & Raise the Vehicle if necessary

  • While using jacks & jack stands, ensure that the weight capacity of the jacks & jack stands is sufficient for your vehicle. It is recommended that you use tools with a weight capacity of approximately 50% of the vehicle’s total weight.
  • Inspect your user manual for the right positions of the jack, and then place it under the car’s frame as instructed. If you only have to raise one wheel, lift the vehicle from the corner where the wheel is located. You should select a jack point that is in the center of the front or back sides or frame if you want to raise the front and the rear of the vehicle.
  • While using jack stands, make sure they’ll be able to near the jack so that they are readily available when you need to use them.
  • A jack can be divided into two categories, the first being scissor jacks and the second being hydraulic jacks.
  • You can also use an extension rod to raise a scissors jack till it attaches with the car’s lift point if you have one of those.
  • You can raise the car frame until the hydraulic jack is in contact with if you have a hydraulic jack. Insert the grip into the body of a jack and smoothly pump the handle to raise the car frame until it is in contact with it.
  • Raise the vehicle to the required height or ground clearance and then lower it back down.

3. Set the Jack stand in their proper locations.

  • Position the stand of a jack under the car frame at a reinforced level or “pinch weld” that is close to where the jack is going to be used to support the vehicle.
  • To adjust the height of a jack stand, pin-type jack stands utilize locking pins, whereas screw-type jack stands utilize adjustable screws.
  • For vehicles with one corner that needs support, place the jack stand underneath the jacking point and adjust its height before locking it in place with a pin as well as screw according to the manufacturer’s instructions. For vehicles with two corners that need support, place the stands under the corners that need support.
  • The car should be slowly lowered to rest on the jack stand after the jack stand has been secured in place.
  • When assisting the front and the rear, choose a set of jack stands that are fixed at equal heights and are constructed in the same manner.
  • In order to raise and support the whole vehicle on 4 jack stands, start by lifting and supporting the front of a vehicle with the first pair of jack stands, and then raise and assist the rear of your car with the second pair of jack stands.
  • As soon as the car is in position, detach the jack & give the vehicle a gentle nudge to make sure that jack stands are securely supporting the vehicle off of the ground.

4. Lower the vehicle

  • When you’re finished, just use a jack to elevate the car an inch or two higher than it was before you started, and then detach the jack stands.
  • Allowing the car to gently descend, slowly turn the jack’s handle or crank in the opposite direction of the car’s movement.
  • Detach the wheel chocks and wedges from the wheels.

5. Make use of a pair of ramps (Optional)

An alternative method of raising a vehicle to its proper height is by using a set of car ramps, as opposed to a jack.

Conclusion

Knowing how to properly use a vehicle jack & jack stands can make sure that one can perform DIY vehicle maintenance tasks like changing a tire and other similar tasks in a safe manner. A safe alternative that might not be as cost-effective or realistic in some cases is to use car elevators or car ramps, which are also available.

 It is much easier to take care of your vehicle when you have a car jack and a jack stand.

Reply